View T370HW02-V4_4263923.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

?copyright au optronics, inc. january, 2003 all rights reserved. t370hw02 v 4 - specs. ver 0.1 1/29 no reproduction and redistribution allowed www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2003 all rights reserved. t370hw02 v4 - specs. ver 0.1 2/29 no reproduction and redistribution allowed update date: 2007/12/18 product specifications 37? hdtv color tft-lcd module model name: t370hw02. v4 () preliminary specifications (*) final specifications www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2003 all rights reserved. t370hw02 v4 - specs. ver 0.1 3/29 no reproduction and redistribution allowed contents no cover contents record of revisions 1 general description 2 absolute maximum ratings 3 electrical specifications 3-1 electrical charactreistic 3-2 interface connections 3-3 signal timing specifications 3-4 signal timing waveforms 3-5 color input data reference 3-6 power sequence 4 optical characteristics 5 mechanical characteristics 6 reliablity 7 international standards 7-1 safety 7-2 emc 8 packing 9 precautions www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2003 all rights reserved. t370hw02 v4 - specs. ver 0.1 4/29 no reproduction and redistribution allowed record of revision version date no old description new description remark 0.1 2007.10.22 first draft 0.2 2007.12.03 3-2 inverter frequency spec 42 ~ 46 khz 3-2 pwm frequency spec 170 ~190 hz 4-1 sec lvds pin assignment auo lvds pin assignment 6-1 color coordinate 0.3 2007.12.18 final spec www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2003 all rights reserved. t370hw02 v4 - specs. ver 0.1 5/29 no reproduction and redistribution allowed 1. general description this specification applies to the 37.0 inch color t ft-lcd module t370hw02 v4. this lcd module has a tft active matrix type liquid crys tal panel 1920x1080 pixels, and diagonal size of 37.0 inch. this module supports 19 20x1080 hdtv mode (non-interlace). each pixel is divided into red, green and blue sub- pixels or dots which are arranged in vertical stripes. gray scale or the brightness of t he sub-pixel color is determined with a 8-bit gray scale signal for each dot. the t370hw02 v4 has been designed to apply the 8-bi t 2 channel lvds interface method. it is intended to support displays where high brigh tness, wide viewing angle, high color saturation, and high color depth are very important . the t370hw02 v4 model is rohs verified which can b e distinguished on panel label. * general information items specification unit note active screen size 37.01 inch display area 819.36 (h) x 460.89(v) mm outline dimension 877(h) x 514.6(v) x 54.3(d) mm wi th inverter driver element a-si tft active matrix display colors 8 bit, 16.7m colors number of pixels 1920 x 1080 pixel pixel pitch 0.42675(h) x 0.42675(w) mm pixel arrangement rgb vertical stripe display operation mode transmissive, normally black surface treatment ag-sr6, 3h haze = 11 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2003 all rights reserved. t370hw02 v4 - specs. ver 0.1 6/29 no reproduction and redistribution allowed 2. absolute maximum ratings the following are maximum values that, if exceeded, may cause permanent damage to the device. item symbol min max unit note logic/lcd drive voltage vcc -0.3 14 [volt] [1] input voltage of signal vin -0.3 4 [volt] [1] blu input voltage vddb -0.3 27 [volt] [1] blu brightness control voltage vblon -0.3 7.0 [volt ] [1] operating temperature top 0 50 [ o c] [2] operating humidity hop 10 90 [%rh] [2] storage temperature tst -20 60 [ o c] [2] storage humidity hst 10 90 [%rh] [2] panel surface temperature pst 65 [ o c] note 1: duration = 50msec note 2 : maximum wet-bulb should be 39 and no conde nsation. the relative humidity must not exceed 90% non-conde nsing at temperatures of 40 or less. at temperature s greater than 40 , the wet bulb temperature must not exceed 39 . www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2003 all rights reserved. t370hw02 v4 - specs. ver 0.1 7/29 no reproduction and redistribution allowed 3. electrical characteristics the t370hw02 v4 requires two power inputs. one is e mployed to power the lcd electronics and to drive t he tft array and liquid crystal. the second input powe r for the blu, is to power inverter.. 3-1 electrical characteristics (ta=25 2 o c) values parameter symbol min typ max unit notes power supply input voltage vcc 10.8 12.0 13.2 vdc power supply input current icc 1 1.2 a [1] power consumption pc - 12 14.4 watt [1] inrush current i rush - 4 apeak [2] differential input high threshold voltage v th 100 mv [3] differential input low threshold voltage v tl -100 mv [3] lvds interface common input voltage v icm 1.1 1.25 1.4 v input high threshold voltage v ih (high) 2.4 3.3 vdc cmos interface input low threshold voltage v il (low) 0 0.9 vdc life time 50000 hours note : 1. the ripple voltage should be controlled under 10% o f v cc 2. vcc=12.0v, = v f 60hz, fclk=65mhz , 25 , test pattern : white pattern 3. measurement condition : t rush = 470 s 100% 90% 10% gnd figure 1: measurement of i rush www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2003 all rights reserved. t370hw02 v4 - specs. ver 0.1 8/29 no reproduction and redistribution allowed 4. measurement of lvds differential voltage is shown i n figure 2. vth vcim vtl 0v 5. the performance of the lamp in lcm, for example lif e time or brightness, is extremely influenced by the characteristics of the dc-ac inverter. so all t he parameters of an inverter should be carefully designed so as not to produce too much leakage curr ent from high-voltage output of the inverter. when you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. when you confirm it, the lcd assembly should be operated in the same condition a s installed in your instrument. 6. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to conducting tape, tft-lcd module have a low luminance and the inverte r has abnormal action because leakage current occurs between lamp wire and conducting tape. 7. the relative humidity must not exceed 80% non-conde nsing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temperat ure must not exceed 39 . when operate at low temperatures, the brightness of ccfl will drop and the life time of ccfl will be reduced. 8. the measured data is without boost function 9. w/o boost function lifetime is defined and judged f or lamp when analog and pwm dimming are maximum values. with boost function lifetime is def ined and judged for lamp when boost function is high (3.3v) figure 2 : lvds differential voltage www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 9/29 no reproduction and redistribution allowed 3-2 interface connections lcd connector (cn3): jae fi-re51s-hf no signal no signal 1 gnd 27 gnd 2 reserved. 28 re0- 3 reserved. 29 re0+ 4 reserved. 30 re1- 5 reserved. 31 re1+ 6 reserved. 32 re2- 7 lvds sel 33 re2+ 8 reserved. 34 gnd 9 reserved. 35 reclkin- 10 reserved. 36 reclkin+ 11 gnd 37 gnd 12 ro0- 38 re3- 13 ro0+ 39 re3+ 14 ro1- 40 n.c. 15 ro1+ 41 n.c. 16 ro2- 42 gnd 17 ro2+ 43 gnd 18 gnd 44 gnd 19 roclkin- 45 gnd 20 roclkin+ 46 gnd 21 gnd 47 n.c. 22 ro3- 48 vlcd(12v) 23 ro3+ 49 vlcd(12v) 24 n.c. 50 vlcd(12v) 25 n.c. 51 vlcd(12v) 26 gnd note: 1. all gnd (ground) pins should be connected togeth er and should also be connected to the lcd?s metal frame. all vcc (power input) pins should be connected together. 2. nc only ? pull high or low is not allowed www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 10/29 no reproduction and redistribution allowed lvds option = l (gnd) or open = ns b4 na de de b4 b5 b6 b7 na b5 r2 r7 g2 g2 r2 r3 r4 r5 r6 r3 g3 b2 b3 b3 g3 g4 g5 g6 g4 previous cycle current cycle next cycle clock rin0+ rin0- rin1+ rin1- rin2+ rin2- r0 b1 na na r0 r1 g0 g1 b0 r1 rin3+ rin3- g7 lvds option = h (3.3v) jeida b2 na de de b2 b3 b4 b5 na r0 r5 g0 g0 r0 r1 r2 r3 r4 r1 g1 b0 b1 b1 g1 g2 g3 g4 g5 g2 previous cycle current cycle next cycle clock rin0+ rin0- rin1+ rin1- rin2+ rin2- r6 b7 na na r6 r7 g6 g7 b6 r7 rin3+ rin3- b3 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 11/29 no reproduction and redistribution allowed backlight connector pin configuration 1. electrical specification spec item symbol condition min typical max unit note input voltage v ddb 21.6 24 26.4 vdc input current i ddb vddb=24v - 6.04 6.62 adc 1 input power p ddb vddb=24v - 145 159 w 1 inrush current i rush vddb=24v - - 8.5 adc 2 output frequency f bl vddb=24v 42 44 46- khz on 2 - 5 on/off control voltage v blon off vddb=24v 0 - 0.8 vdc max 2 - 3.3 vdc dimming control voltage v dim min vddb=24v 0 0.8 vdc dimming frequent f d vddb=24v 180 hz max vddb=24v - 3.3 - vdc pwm control voltage v_epwm min vddb=24v - 0 - external pwm control current i_epwm vddb=24v 2 madc external pwm duty ratio d_epwm vddb=24v 10 100 % external pwm frequency f_epwm vddb=24v 170 180 190 hz note 1: vdim= 3.3v; epwm = open/high (turn on for 4 5minutes) note 2 : measurement condition rising time = 20 ms (vddb : 10%~90%); note 3 : (a) uniformity and flicker does not guaran tee under 10% dimming control. (b) 10% dimming function okay and no backlig ht shut down www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 12/29 no reproduction and redistribution allowed 2. inverter units connector is shown below: ci0114m1hr0-lf matt : jst or civilux or equivalent pin no symbol description 1 vbl 24v 2 vbl 24v 3 vbl 24v 4 vbl 24v 5 vbl 24v 6 gnd ground 7 gnd ground 8 gnd ground 9 gnd ground 10 gnd ground 11 nc n.c. 12 vblon bl on-off : high/open(3.3 ~ 5v) for bl on,lo w(gnd) for off 13 internal pwm high (3.3v,100% duty)for 100% 14 nc n.c. note: pin 13 & pin 14 can not connect at the same t ime www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 13/29 no reproduction and redistribution allowed 3-3 signal timing specifications this is the signal timing required at the input of the user connector. all of the interface signal tim ing should be satisfied with the following specifications for it? s proper operation. timing table (de only mode) a. frame rate = 60 hz b. frame rate = 50 hz 1.) di splay position is specific by the rise of de signal only. horizontal display position is specified by the fal ling edge of 1 st dclk right after the rise of enab, is displayed on the left edge of the screen. vertical display position is specified by the rise of de after a ?low? level period equivalent to eigh t times of horizontal period. the 1 st data corresponding to one horizontal line after th e rise the of enab is displayed at the top line of screen. 3.) if a period of deb ?high? is less than 1920 dcl k or less than 1080 lines, the rest of the screen d isplays black. 4.) the display position does not fit to the screen if a period of de ?high? and the effective data pe riod do not synchronize with each other. www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 14/29 no reproduction and redistribution allowed 3-4 signal timing waveforms th tdisp(v) tblk(v) tv de rgb data n line invalid data invalid data 1 line 2 line 3 line n line 4 line tclk clk de rgb data (odd) rgb data (even) pixel m-7 pixel m-5 pixel m-3 pixel m-1 pixel m-6 pixel m-4 pixel m-2 pixel m invalid data invalid data pixel 1 pixel 2 pixel 3 pixel 5 pixel 4 pixel 6 pixel 7 pixel 8 pixel 9 pixel 10 pixel 11 pixel 12 pixel m-5 pixel m-3 pixel m-1 pixel m-4 pixel m-2 pixel m invalid data invalid data pixel 1 pixel 2 pixel 3 pixel 4 th tdisp(h) tblk(h) www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 15/29 no reproduction and redistribution allowed 3-5 color input data assignment the brightness of each primary color (red, green an d blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter th e color. the table below provides a reference for c olor versus data input. color data reference input color data red msb lsb green msb lsb blue msb lsb color r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ---- green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 green green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ------- blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 blue blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 16/29 no reproduction and redistribution allowed 3-6 power sequence of lcd module of auo-043(on/off) 3.6.1 power sequence for lcd 10% 90% 90% 10% t1 t2 t3 t4 t5 t6 t7 lamp on valid data power supply for lcd signal backlight note: the timing controller will not be damaged in cas e of tv set ac input power suddenly shut down. once power reset, it should follow power sequenc e as spec. definition. (1) apply the lamp voltage within the lcd operation ran ge. when the back-light turns on before the lcd operation or the lcd turns off before the back-ligh t turns off, the display may momentarily become abnormal screen. values parameter min. typ. max. units min. t1 470 - 5000 us t2 20 - 35 ms t3 500 - - ms t4 200 - - ms t5 5 - - ms t6 - - 30 ms t7 1 - - s www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 17/29 no reproduction and redistribution allowed 3.6.2 power sequence of inverter values parameter min. typ. max. units t1 20 - - ms t2 500 - - ms t3 250 - - ms t4 0 - - ms t5 1 - - ms t6 - - 10 ms www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 18/29 no reproduction and redistribution allowed 4. optical specification optical characteristics are determined after the un it has been ?on? and stable for approximately 45 mi nutes in a dark environment at 25 . the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0. testing condition: fig.1 measurement equipment value units notes parameter symbol condition min. typ. max. contrast ratio cr 2200 2500 1 surface luminance, white lwh 400 500 cd/ O 2 luminance variation white 9 pts 1.3 cd/ O 3 response time gray to gray t 6.5 ms 4 color gamma ntsc 72 % r x 0.64 red r y 0.33 g x 0.29 green g y 0.6 b x 0.15 blue b y 0.06 w x 0.280 color coordinates (cie 1931) white w y =0 o , =0 o viewing normal angle typ -0.03 0.290 typ +0.03 x axis, right r ( =0 ) 89 5 x axis, left l ( =180 ) 89 y axis, up u ( =90 ) 89 viewing angle y axis, down d ( =0 ) cr 10 89 degree (ta=25 2 o c) www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 19/29 no reproduction and redistribution allowed note : 1. contrast ratio will be measured in the center of pa nel (point 5 in figure 2), contrast ratio (cr) is d efined mathematically as: surface luminance of l on5 contrast ratio= surface luminance of l off5 2. surface luminance is luminance value at point 5 acr oss the lcd surface 50cm from the surface with all pixels displaying white. from more information see fig 2. when vddb = 24v, iddb = 6.04a. l wh =lo51. where lon5 is the luminance with all pixels displaying white at center 5 location. 3. the variation in surface luminance, white is defined (center of screen) as: white(9p) = maximum(l on1 , l on2 ,?,l on9 )/ minimum(l on1 , l on2 ,?l on9 ) 4. response time t is the average time required for display transitio n by switching the input signal for five luminance ratio (0%,25%,50%,75%,100% brightness mat rix) and is based on f v =60hz to optimize. 5. viewing angle is the angle at which the contrast ra tio is greater than 10. the angles are determined f or the horizontal or x axis and the vertical or y axis wit h respect to the z axis which is normal to the lcd surface. for more information see fig4. fig. 2 luminance measurement positions the response time is defined as the following figur e and shall be measured by switching the input sign al for ?any level of gray(bright) ? and ?any level of gray (dark)?. www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 20/29 no reproduction and redistribution allowed fig.3 measurement of response time fig.4 measurement of viewing angle any level of gray (dark) any level of gray (bright) any level of gray (bright) www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 21/29 no reproduction and redistribution allowed 5. mechanical characteristics the contents provide general mechanical characteris tics for the model t370hw02 v4. detailed mechanical drawings are shown in the following pages. horizontal 877.0 mm vertical 514.6mm outline dimension depth 54.3 mm(with inverter) horizontal 827.8 mm bezel opening vertical 469.4 mm horizontal 819.36 mm active display area vertical 460.89 mm weight 10000g (typ.) www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 22/29 no reproduction and redistribution allowed mechanical figure: www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 23/29 no reproduction and redistribution allowed www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 24/29 no reproduction and redistribution allowed 6. reliability environment test condition: test items q'ty conditions 1 high temperature stroage 3 60 300 hrs 2 low temperature stroage 3 -20 , 300 hrs 3 high temperature operation 3 50 , 300 hrs 4 low temperature operation 3 -5 , 300 hrs 5 vibration (non-operation) 3 (10 ~ 300hz/1.5g/11min sr, xyz 30min/axis) vibration level : 1.5g rms, bandwidth : 10-300hz duration: x, y, z 30min, 6 shock (non-operation) 3 shock level: 50g waveform: have sine wave, 11ms direction: x,y, z one time each direction 7 vibration (with carton) 3 random wave (1.5 grms 10~200hz) 30mins / per each x.y.z axes 8 drop (with carton) 3 height: 38cm 1 corner, 3 edges, 6 surfaces (astmd4169-i) www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t370hw02 v4 25/29 no reproduction and redistribution allowed 7. international standard 7-1 safety (1) ul1950 third edition, underwriters laboratories, in c. jan. 28, 1995 standard for safety of information technology equip ment including electrical business equipment. (2) can/csa c22.2 no. 950-95/60950 third edition, canad ian standards association, standard for safety of information technology equip ment including electrical business equipment. (3) en60950: 1992+a2: 1993+a2: 1993+c3: 1995+a4: 1997+a 11: 1997 iec 950: 1991+a1: 1992+a2: 1993+c3: 1995+a4:1996 european committee for electrotechnical standardiza tion (cenelec) european standard for safety of information technol ogy equipment including electrical business equipment. 7-2 emc a) ansi c63.4 ?methods of measurement of radio-noise e missions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. ?american national standards institute(ansi), 1992 b) c.i.s.p.r ?limits and methods of measurement of radio interface characteristics of information technology equipment.? international sp ecial committee on radio interference. c) en 55022 ?limits and methods of measurement of radi o interface characteristics of information technology equipment.? european committ ee for electrotechnical standardization. (cenelec), 1998 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 26/29 no reproduction and redistribution allowed 8. packing a. panel label: tw6562700014-zmao0 tw: t: taiwan, a/b: china 00014: panel serial number zma: auo internal code b. carton label: 370hw02 v4 t370hw02 v4 97.37t04.4xx www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 27/29 no reproduction and redistribution allowed packing methods: packing specification: specification item qty. dimension weight (kg) packing remark 1 packing box 3 pcs/box 965(l)mm*280(w)mm*610(h)mm 30 2 pallet 1 1140(l)mm*980(w)mm*140(h)mm 15 3 boxes per pallet 8 boxes/pallet (by air) ; 12 box es/pallet (by sea) 4 panels per pallet 24pcs/pallet(by air) ; 36 boxes /pallet (by sea) pallet after packing 24 (by air) 36(by sea) 1140(l)mm*980(w)mm*1360(h)mm (by air) 1140(l)mm*980(w)mm*2110(h)mm (by sea) 257 (by air) 393 (by sea) www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 28/29 no reproduction and redistribution allowed 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1 mounting precautions (1) you must mount a module using holes arranged in fou r corners or four sides. (2) you should consider the mounting structure so that uneven force (ex. twisted stress) is not applied to module. and the case on which a module i s mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protective pl ate to the surface in order to protect the polarizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for th e cover case are not desirable because the former generates corrosive gas of attacking the pol arizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer wit h glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clo thes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cl oth. (some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene . normal-hexane is recommended for cleaning the adhesives used to attach front/ rear p olarizer. do not use acetone, toluene and alcohol because they cause chemical damage to the p olarizer. (8) wipe off saliva or water drops as soon as possible. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2 operating precautions (1) the device listed in the product specification shee ts was designed and manufactured for tv application (2) the spike noise causes the mis-operation of circuit s. it should be lower than following voltage: v= 200mv(over and under shoot voltage) (3) response time depends on the temperature. (in lower temperature, it becomes longer..) (4) brightness of ccfl depends on the temperature. (in lower temperature, it becomes lower.) and in lower temperature, response time (required time that brightness is stable after turned on) becomes longer. (5) be careful for condensation at sudden temperature c hange. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (6) when fixed patterns are displayed for a long time, remnant image is likely to occur. (7) module has high frequency circuits. sufficient supp ression to the electromagnetic interference shall be done by system manufacturers. grounding an d shielding methods may be important to minimize the interface. www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. sep, 2006 all rights reserved. t37 0hw02 v4 29/29 no reproduction and redistribution allowed 9-3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground thro ugh wristband etc. and don?t touch interface pin di rectly. 9-4 precautions for strong light exposure strong light exposure causes degradation of polariz er and color filter. 9-5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the modul e to sunlight or fluorescent light. keep the temperature between 5 and 35 at normal humidity. (2) the polarizer surface should not come in contact wi th any other object. it is recommended that they be stored in the container in which they were shipp ed. 9-6 handling precautions for protection film (1) the protection film is attached to the bezel with a small masking tape. when the protection film is peeled off, static electricity is generated between the film and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) when the module with protection film attached is st ored for a long time, sometimes there remains a very small amount of flue still on the bezel after the protection film is peeled off. (3) you can remove the glue easily. when the glue remai ns on the bezel or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of T370HW02-V4

	To Download T370HW02-V4 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .